Installing A Bath tub
Installing A Bath tub
Blog Article
This article following next in relation to Installing A Bathtub is highly insightful. Try it and make your own assumptions.
Setting up a bathtub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably difficult job. If the old tub is easily accessible, the task can move immediately; if you have to open up a wall to eliminate the old tub and also position the brand-new bathtub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will require an assistant to leave the old bathtub and embeded in the brand-new one. Ensure you have certified yourself for the task and also are comfortable trying it. As opposed to hiring a service provider to take control of a halfway-completed project, it is far better to consider utilizing one prior to you start. Chances are you might require an expert plumber to make tube links.
This short article will certainly aid you install a new bath tub in your bathroom if you have currently gotten a brand-new tub and do not need to change the setup of your previous water pipes.
Your tools as well as product list ought to make up the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain any water remaining in the system. The procedure of removing the existing taps can be quite troublesome because of the restricted gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in area between the tap and also the sink. Protect the tap in place with the supplier provided backnut. As soon as the faucet is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The former kind must be connected to the faucet ends first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Making use of both wooden boards under its feet, place the bath tub in the required placement. The wooden boards are helpful in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bath tub until the level reads level.
To mount faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression join; after that do the exact same for the various other tap.
Activate the water supply as well as check all joints and new pipework for leakages and tighten them if needed. Fill the tub as well as likewise examine the overflow outlet as well as the regular electrical outlet for leakages.
Finally, repair the bath paneling as described in the supplier's instruction manual. Tiling and also sealing around the tub needs to wait up until the bath tub has been utilized at the very least once as this will resolve it into its final setting.
Planning for the Installation
First of all, the sustaining frame supplied with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets device to prevent strain on the tub.
Fit the versatile faucet adapters to the bottom of both taps using 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final placement.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, triggering the water to penetrate the wall between the bath and the tiling, bring about issues with moisture and feasible leakages to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water prior to securing, to allow for the activity experienced when the tub remains in use. The sealant can split fairly very early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the market. It is a good idea to fit the floor tiles using waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our part about Installing A Bathtub. Thanks a ton for spending some time to browse our piece of content. Are you aware of another individual who is enthusiastic about A Step-by-Step Guide to Installing a Bathtub? Do not hesitate to promote it. Thank you so much for your time spent reading it.
Website
Report this page